Metal/Nonmetal

Fatality #11 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m11On May 1, 2014, a 57-year-old co-owner with 1 year of experience was killed at a gypsum mine.  The victim was driving an all terrain vehicle on the mine site to place signs around the perimeter of the mine.  He lost control of the vehicle while traveling on a steep hill and it overturned onto him.

Best Practices

  • Ensure that persons are trained to understand the hazards associated with the work being performed.
  • Ensure that operators are properly task trained before operating mobile equipment they may not be familiar with.
  • Maintain operating speeds consistent with road grades and conditions.
  • Load equipment and/or supplies properly on mobile equipment to ensure stability during operation.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #10 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m10
On April 28, 2014, a 53-year-old miner with 32 years of experience was killed at an underground gold mine. The victim was drilling with a jackleg drill when his clothing became entangled in the drill steel of the machine.
Best Practices

  • Ensure that persons are trained, including task-training, to understand the hazards associated with the work being performed.
  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and use methods to properly protect persons.
  • Conduct work place examinations before beginning any work.
  • Do not place yourself in a position that will expose you to hazards while performing a task.
  • Stop the drill rotation when performing tasks near the rotating steel.
  • Provide safe routing of hoses and cables so they are not close to the rotation of the drill.
  • Do not assign a person to work alone in areas where hazardous conditions exist that would endanger his or her safety.
  • Do not wear loose fitting clothing when working around drilling machinery.
  • Keep work areas clean and free of tripping hazards.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #9 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m09On February 27, 2014, a 27-year-old contract mechanic with 2 years of experience was injured at an underground limestone mine.  The victim was repairing a hydraulic pump on a scaler when fell from an attached walkway approximately five feet to the ground.  He was airlifted to a hospital where he died the next day.

Best Practices

  • Ensure that persons are trained, including task-training, to understand the hazards associated with the work being performed.
  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and use methods to properly protect persons.
  • Conduct work place examinations before beginning any work.
  • Do not place yourself in a position that will expose you to hazards while performing a task.
  • Ensure effective gates, safety chains, or railings are used and properly maintained where openings may exist that could pose a hazard.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #8 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m08On April 24, 2014, a 50-year-old contract dozer operator with 23 years of experience was killed at a fire clay mine.  He had been operating a dozer pushing clay in the pit and was found lying five feet behind the dozer.

Best Practices

  • Ensure that persons are trained, including task-training, to understand the hazards associated with the work being performed.
  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and use methods to properly protect persons.
  • Do not place yourself in a position that will expose you to hazards while performing a task.
  • Maintain control of mobile equipment while it is in motion.
  • Set the parking brake and lower the bull dozer blade to the ground before dismounting equipment.
  • Never jump from mobile equipment.
  • Always wear a seat belt when operating mobile equipment.
  • Monitor persons routinely to determine safe work procedures are followed.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #7 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m07On April 17, 2014, a 58-year-old truck driver with 3½ years of experience was killed at a sand and gravel mine. An excavator was loading material in a haul truck parked at the pit. When the victim exited the truck, he was struck by the excavator bucket and pinned against the truck.

Best Practices

  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and use methods to properly protect persons.
  • Task train all persons to recognize all potential hazardous conditions and to understand safe job procedures for elimination of the hazards before beginning work.
  • Ensure that haul truck operators remain in their trucks when being loaded.
  • Communicate with mobile equipment operators and ensure they acknowledge your presence.  Stay in the line of sight with mobile equipment operators.
  • Ensure that you make eye contact with mobile equipment operators before approaching their work areas.  Never assume the equipment operator sees you.
  • Never place yourself in a location where equipment operators can’t see you.
  • Before operating equipment, always ensure other miners are clear and safely  positioned.
  • Monitor persons routinely to determine safe work procedures are followed.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #5 & #6 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m05-06On April 11, 2014, a 53-year-old scaler with 8 years of experience and a 29-year old scaler with 8 years of experience were killed at an underground limestone mine.  The miners were in a basket on a boom truck scaling a pillar about 40 feet above the mine floor.  Large slabs of rock fell from the rib and struck an outrigger and the back of the truck, causing the boom to fall to the mine floor. 

Best Practices

  • Establish safe work procedures and train all persons to recognize and understand these procedures.
  • Discuss safe work procedures before beginning work.  Identify and control all hazards associated with the work to be performed and the methods to properly protect persons.
  • Always examine, sound, and test for loose ground in areas before starting to work, after blasting, and as ground conditions warrant.
  • Always wear fall protection where there is a danger of falling.
  • Scale loose material from a safe position and location.
  • Test for loose material frequently during work activities.
  • Install ground support in roof and ribs where conditions warrant.
  • Use equipment with a reach that reduces the possibility of the equipment being struck by falling material.
  • Position equipment to keep outriggers and boom from being struck by falling material.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #4 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

FAB14m04_clip_image004FAB14m04_clip_image002On March 27, 2014, a 64-year-old foreman with 32 years of experience was seriously injured when he was struck by a section of plastic water pipe as it was being moved by an excavator.  The victim was transported to a hospital where he died on March 30, 2014, as a result of his injuries.

Best Practices

  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and the methods to properly protect persons.
  • Task train all persons to recognize all potential hazardous conditions and to understand safe job procedures for elimination of the hazards before beginning work.
  • Wear suitable hard hats where falling objects may create a hazard.
  • Stay clear of a suspended load.
  • Attach taglines to loads that may require steadying or guidance while suspended.
  • Implement measures to ensure persons are properly positioned and protected from hazards while performing a task.
  • Monitor persons routinely to determine safe work procedures are followed.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #3 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

FAB14m03_clip_image002
On February 28, 2014, a 50-year old supervisor with 27 years of experience was killed at a sand and gravel mine.  The victim was at a backfill site and approached an 80-foot high bank when it failed, engulfing him.

Best Practices

  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and the methods to properly protect persons.
  • Task train all persons to recognize all potential hazardous conditions that can decrease bank or slope stability and ensure they understand safe job procedures for elimination of the hazards.
  • Prior to beginning work and as ground conditions warrant during the shift, examine all pit, highwall, slope, and bank conditions.  Be especially vigilant for these conditions after each rain, freeze, or thaw.
  • Use mining methods that ensure pit, highwall, slope, and bank stability and safe working conditions.
  • Correct hazardous conditions by working from a safe location.
  • Stay clear of potentially unstable areas.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #2 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m02

On February 21, 2014, a 34-year old contract laborer with 6 months of experience was killed at a cement operation when attempting to access an elevator in the finish mill. When the victim opened the elevator door on the fourth floor landing, he stepped into the elevator shaft and fell approximately 51 feet to the top of the elevator car located on the ground floor.

Best Practices

  • Immediately report any elevator problems to management.
  • Ensure that any problems affecting the safety of an elevator are repaired promptly.
  • Ensure that elevator door interlocks, that prevent the door from being opened unless the elevator car is present, are functional.
  • Ensure that elevator doors will not open unless an elevator car is at the floor landing.
  • Install audible signals that sound when the elevator car is at the landing prior to the doors opening.
  • Train all persons to be aware of their surroundings when entering or exiting an elevator car.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #1 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

ftl2014m01On February 1, 2014, a 56-year old contract belt operator with 4 months of experience was killed at an iron ore mine. The victim was cleaning a return idler inside the frame of a belt conveyor when he became entangled between the return idler and the belt.

Best Practices

  • Establish policies and procedures for conducting specific tasks on belt conveyors.
  • Before beginning any work, ensure that persons assigned to clean belt conveyors are task trained and understand the hazards associated with the work to be performed.
  • Do not perform work on a belt conveyor until the power is off, locked, and tagged, and machinery components are blocked against motion.
  • Never clean pulleys or idlers manually while belt conveyors are operating.
  • Identify hazards around belt conveyor systems, design guarding, and securely install the guarding to ensure miners do not contact moving parts.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).