Metal/Nonmetal

Fatality #2 for Metal/Nonmetal Mining 2013

renewcomerLeave a comment

ftl2013m02

On January 21, 2013, a 54-year old mechanic with 6 years of experience was killed at a lime operation. The victim went to a kiln pre-heat deck to repair a leaking hydraulic cylinder that activates a pusher arm on the kiln. He was caught between the corner of the angle iron and the plate connecting the push rods.

Best Practices
 

  • Establish and discuss safe work procedures. Identify and control all hazards associated with the work to be performed along with the methods to properly protect persons.
  • Always follow the equipment manufacturer’s recommended maintenance procedures when conducting repairs to machinery.
  • Task train all persons to recognize all potential hazardous conditions and understand safe job procedures to eliminate all hazards before beginning work.
  • Before working on or near equipment, ensure that the equipment power circuits are locked out/tagged out and that the equipment is blocked against hazardous motion.
  • Require all persons to be positioned to prevent them from being exposed to any hazards.
  • Monitor personnel to ensure safe work procedures, including lock out/ tag out and safe work positioning, are followed.
  • Ensure guarding is in place to cover potential pinch points and moving parts in areas routinely accessed by personnel.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #1 for Metal/Nonmetal Mining 2013

renewcomerLeave a comment

ftl2013m01On January 7, 2013, a 49-year old assistant plant manager with 30 years of experience was injured at a crushed stone operation. The victim was working on a lift, taking samples from a highwall, when a large rock fell and struck him. He was hospitalized and died on January 19, 2013.

Best Practices

  • Establish and discuss safe work procedures for working near highwalls. Identify and control all hazards.
  • Train all persons to recognize adverse conditions and environmental factors that can decrease highwall stability and understand safe job procedures to eliminate all hazards before beginning work.
  • Look, Listen and Evaluate pit and highwall conditions daily, especially after each rain, freeze, or thaw.
  • Remove loose or overhanging material from the face. Correct hazardous conditions by working from a safe location.
  • Ensure that work or travel areas and equipment are a safe distance from the toe of the highwall.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #17 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On November 1, 2012, a 30-year old contract driller with 6 years of experience was killed at a common shale operation. The victim apparently attempted to thread a new drill steel manually, with the use of a strap and the drill head rotating, when the rotating steel entangled him.

Best Practices

  • Establish and discuss safe work procedures. Identify and control all hazards. Train all persons to recognize all potential hazards and understand safe job procedures to eliminate all hazards before beginning work.
  • Ensure that the manufacturer’s procedures are followed when adding drill steels.
  • Ensure that emergency stop/shut-off switches, panic bars, dead man devices, tethers, slap bars, rope switches, two handed controls, spring loaded controls, are functional and in easily accessible locations.
  • Never manually thread drill steels when the drill head is rotating.
  • Drills should be fitted with automated systems for changing rods, or two persons should be present when rods are changed manually.
  • Do not wear loose fitting clothing when working around drilling machinery. Avoid using a strap or other objects that could become entangled with or thrown from moving or rotating parts.
  • Monitor personnel routinely to ensure procedures are followed.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #16 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On October 24, 2012, a 52-year old utility miner with 19 years of experience was killed on the surface of an underground limestone mine. He was operating a forklift, traveling on a decline toward the mine entrance, when the forklift went out of control. The forklift struck a concrete support for the belt conveyor and overturned, killing him.

Best Practices

  • Conduct adequate pre-operational checks and ensure the service brakes are properly maintained and will stop and hold the mobile equipment prior to operating.
  • Ensure that mobile equipment operators are adequately task trained in all phases of mobile equipment operation before performing work.
  • Ensure the load is stable and secured on the forks of the forklift.
  • When descending a grade, operate the forklift with the load in the upgrade position.
  • Maintain control of self-propelled mobile equipment while it is in motion.
  • Operating speeds shall be consistent with conditions of roadways, tracks, grades, clearance, visibility, curves, and traffic.
  • Operate equipment within its designed limitations. Slow down or drop to a lower gear when necessary. Post areas where lower speeds are warranted.
  • Always wear a seat belt when operating self-propelled mobile equipment.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #15 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On October 10, 2012, a 55-year old contract painter with 35 years of experience was killed at a kaolin and ball clay operation. He was standing on the bottom of a 40-foot high, 50-foot diameter tank that was open to the atmosphere and covered with mesh cloth material. He was spraying coal tar on the inside walls of the tank and was found unconscious by coworkers. He was recovered by emergency personnel and pronounced dead at a hospital.

Best Practices

  • Develop, implement, and maintain a written Hazard Communication (HazCom) program.
  • Ensure that a Material Safety Data Sheet (MSDS) is accessible to persons for each hazardous chemical to which they may be exposed.
  • Review and discuss MSDS control section recommendations with employees that may be exposed to hazardous chemicals. Establish and discuss safe work procedures before starting any work and identify and control all hazards.
  • Train all persons to recognize and understand safe job procedures, including the physical and health hazards of chemicals that are being used and the proper use of respiratory protection, gloves, body suits, hearing, and eye & face protection.
  • Ensure that adequate ventilation is provided to all work areas.
  • Ensure that persons are not required to perform work alone in any area where hazardous conditions exist that would endanger their safety.
  • Conduct air monitoring with calibrated instruments to ensure a safe working atmosphere. Air monitoring should be done prior to workers entering the confined work space and continuously till the workers have exited the enclosed area. Atmospheric monitoring at minimum includes Oxygen, LEL and all potential toxic gases in the work place.

Based on MSHA’s investigation and the finding of the death certificate, MSHA later concluded that the miner died from natural causes and that the fatality is not chargeable.

Fatality #14 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On September 26, 2012, a 79-year old foreman with 56 years of experience was killed when he was run over by the dozer he had been operating. The victim exited the cab and was positioned on the left track checking the engine throttle linkage when the dozer moved forward.

Best Practices
 

  • Inspect equipment before placing it in operation for the shift.
  • Correct safety and operational defects on equipment in a timely manner to prevent the creation of a hazard to persons.
  • Establish safe work procedures and identify and remove hazards before beginning a task.
  • Prior to beginning work, ensure that persons are task-trained and understand the hazards associated with the work being performed. Know and follow safe work procedures before beginning repairs.
  • Block dozer against motion by lowering the blade and ripper to the ground and setting the parking brake. Set the transmission lock lever to ensure the transmission is in neutral.
  • Do not place yourself in a position that will expose you to hazards while performing a task.
  • Monitor personnel routinely to determine that safe work procedures are followed.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #13 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On September 22, 2012, a 34-year old contract laborer with 6 days of experience was killed when he fell through a 6 ft. X 8 ft. hole that was partially covered with 2″ X 4″ boards and ¾ ” thick plywood. He fell into a chute landing on a belt conveyor 30 feet below. The victim was assigned fire watch duties on a welding/cutting operation that was taking place on the floor above him.

Best Practices
 

  • Establish and discuss safe work procedures. Identify and control all hazards. Train all persons to recognize and understand safe job procedures before beginning work.
  • Always use fall protection when working where a fall hazard exists.
  • Protect openings near travelways through which persons may fall by installing appropriately designed railings, barriers, or covers.
  • Keep temporary access opening covers secured in place at all times when the opening is not being used. Replace deteriorated floor plating and grating.
  • Ensure that areas are barricaded or have warning signs posted at all approaches if hazards exist that are not immediately obvious.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #12 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On August 17, 2012, a 58-year old equipment operator with 19 years of experience was killed at a cement operation. The victim was working on the roof of a 189-foot tall silo when the roof collapsed. Rescuers responded immediately and recovered the victim on September 4, 2012.

Best Practices
 

  • Routinely inspect the entire silo including walls, top, hopper(s), feeders, conveying equipment, liner, roof vents, etc. Look for structural damage, exposed rebar, stress cracks, corrosion, concrete spalling/cracking, signs of overfilling, top lifts, dust spills from seams during loading, damage to climbing devices, etc. The structure should be inspected by a professional engineer knowledgeable in silo design and construction.
  • Ensure a competent person conducts examinations to identify hazards.
  • If damage is discovered, prohibit use of and access on the silo and in the surrounding area until repairs are complete and/or a registered professional engineer has declared it structurally safe to use.
  • Modifications or equipment additions to a silo should be under the direction of a professional engineer.
  • Ensure process controls and dust collector baghouses are in working order to prevent overpressure, overfilling, or excessive vacuum. Dust leaving a silo may indicate structural damage or equipment malfunction.
  • Ensure aeration systems and other means of enhancing hopper flow are in working order so asymmetric flow patterns do not develop within the silo and damage the walls, hopper, and roof.
  • Provide silo level probes/weight measuring technology for /equipment to monitor silo material filling and discharge in the silo and keep it in working order.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #11 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On August 31, 2012, a 49-year old driller with 24 years of mining experience was killed at an underground gold mine. The victim was assigned to prepare the work area to set up a long-hole bench drill and was working near an open stope when he fell down the stope. He was inadvertently loaded out with the material and transported by a haul truck to the surface where he was later discovered.

Best Practices
 

  • Always use fall protection with a lanyard anchored securely when working where there is a danger of falling.
  • Examine workplaces for changing conditions when the strata, drill patterns, or other workplace conditions change.
  • Establish policies and procedures for safely clearing hung or stuck material and ensure that persons follow those safe policies and procedures.
  • Ensure that persons are task-trained and understand the hazards associated with the work being performed.
  • Ensure that areas are barricaded or have warning signs posted at all approaches where hazards exist that are not immediately obvious.
  • Consider using a “miner in distress” call feature available on many communication and tracking systems carried by miners. This feature is designed to improve emergency response if a miner working alone or out of sight of other miners requires immediate assistance.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #10 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On July 26, 2012, a 49-year old equipment operator with 18 weeks of mining experience was killed at a portable crushing operation. He was standing on the discharge end of a 150-foot stacker belt conveyor, greasing the head pulley, when a coworker started the conveyor. The victim fell off the conveyor approximately 50 feet to the ground below.

Best Practices
 

  • Provide and maintain a safe means of access to all working places.
  • Establish policies and procedures for conducting specific tasks on belt conveyors.
  • Ensure that persons are task trained and understand the hazards associated with the work being performed.
  • Deenergize and Lock-out/tag-out all power sources before working on belt conveyors.
  • Block belt conveyors against motion before working near a drive, head, tail, and take-up pulleys.
  • Maintain communications with all persons performing the task. Before starting belt conveyors, ensure that all persons are clear.
  • Sound an audible alarm prior to start up, if the entire length of the belt conveyor is not visible from the starting switch.
  • Clearly label all switches on equipment and provide training to persons who operate and work in the vicinity of equipment.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).