Metal/Nonmetal

Fatality #9 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On June 21, 2012, a 49-year old customer truck driver with no mining experience was killed at a surface stone mine. He was driving a loaded dump truck, traveling down a grade, when the truck lost its brakes and went out of control. The victim jumped out and the truck ran over him. A passenger in the truck also jumped out and was treated at a hospital and released.

  • Ensure that mobile equipment operators are task trained adequately and demonstrate proficiency in all phases of mobile equipment operation before performing work.
  • Maintain equipment braking systems in good repair and adjustment.
  • Conduct adequate pre-operational checks to ensure the service brakes will stop and hold the mobile equipment prior to operating.
  • Know the truck’s capabilities, operating ranges, load-limits and safety features.
  • Operators of self-propelled mobile equipment shall maintain control of the equipment while it is in motion.
  • Operating speeds shall be consistent with conditions of roadways, tracks, grades, clearance, visibility, curves, and traffic.
  • Slow down or shift to a lower gear when necessary. Post areas where lower speeds are warranted.
  • Always wear a seat belt when operating self-propelled mobile equipment.
  • Do not attempt to exit or jump from moving mobile equipment.
  • Provide adequate site specific hazard training to all customer truck drivers.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #8 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On May 28, 2012, a 51-year old shift operator with 13 years of experience was killed at a cement operation. The victim was found near the plant’s crane bay building after being struck by a front-end loader. He was walking from the lunchroom toward the locker area.

Best Practices

  • Train all persons to stay clear of mobile equipment.
  • Be aware of the location and traffic patterns of mobile equipment in your work area.
  • Wear high visibility clothing when working around mobile equipment.
  • Before moving mobile equipment, look in the direction of travel and use all mirrors and cameras to ensure no persons are in the intended path.
  • Sound the horn to warn persons of intended movement and give them time to move to a safe location.
  • Operate the mobile equipment at reduced speeds in work areas.
  • Ensure that backup alarms and lights on mobile equipment are maintained and operational.
  • Post signs to warn persons in areas where mobile equipment travel.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #7 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On May 23, 2012, a 36 year-old foreman with about 9½ years of experience was killed at a sand and gravel operation. He was operating an excavator on a dike separating two ponds. The ground beneath the excavator tracks failed and the excavator toppled into one of the ponds.

Best Practices

  • Examine work areas to identify all hazards and remediate before starting any work.
  • Evaluate the stability of the ground (slopes and berms) prior to operating equipment near any drop off or edge.
  • Always be attentive to changes in ground conditions and visibility when operating machinery.
  • Perform the work at a safe distance away from the edge of a pond or where the stability of the ground may be unknown.
  • If a potential hazard is present, use long reach equipment to limit exposure and maintain a safe distance away.
  • Consider areas that have experienced previous slope failures to be unstable and do not approach until the area is evaluated for stability.
  • Wear flotation devices where there is a danger of falling into water.
  • Be alert to changes in ground conditions such as cracking, bulging, sloughing, undercutting, and erosion.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #6 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

Best Practices

  • Ensure that mobile equipment operators are task trained adequately and demonstrate proficiency in all phases of mobile equipment operation before performing work.
  • Conduct adequate pre-operational checks and ensure the service brakes are properly maintained and will stop and hold the mobile equipment prior to operating.
  • Operators of self-propelled mobile equipment shall maintain control of the equipment while it is in motion.
  • Operating speeds shall be consistent with conditions of roadways, tracks, grades, clearance, visibility, curves, and traffic.
  • Ensure that equipment manufacturer’s load limits are not exceeded.
  • Slow down or drop to a lower gear when necessary. Post areas where lower speeds are warranted.
  • Always wear a seat belt when operating self-propelled mobile equipment.
  • Ensure that equipment operators maintain adequate communications.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #5 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On April 11, 2012, a 49 year-old excavator operator with approximately 8½ years of experience was injured at a sand and gravel operation. The victim was removing bolts from a counterweight on the back of an excavator when the counterweight fell and struck him. He was hospitalized and died on April 12, 2012, as a result of his injuries.

Best Practices

  • Before working on or near equipment, establish safe work procedures consistent with the design of the machine. Train all persons to recognize and understand these procedures.
  • Follow the equipment manufacturer’s procedures for the work being performed to ensure that all hazards are addressed.
  • Provide adequate task training to persons assigned to perform the work. Utilize assistance from the manufacturer when the equipment incorporates new technology and features.
  • Install blocking materials before removing mounting bolts from machinery components which can fall during disassembly.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #4 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On March 20, 2012, a 54 year-old mine owner with approximately 25 years of experience was killed at an underground gemstone mine. He was cleaning fine ore with a shovel and loading it in the bucket of a front-end loader when rock fell from the top left rib about 20 feet high. The victim was working alone.

Best Practices

  • Examine work areas and identify and control all hazards before starting any work.
  • Establish safe work procedures and train all persons to recognize and understand these procedures.
  • Always examine, sound, and test for loose ground in areas before starting to work, after blasting, and as ground conditions warrant.
  • Test for loose material frequently during work activities and where necessary, scale loose material safely.
  • Install ground support in roof and ribs where conditions warrant.
  • Do not perform work alone in any area where hazardous conditions exist that would endanger your safety.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #3 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On February 22, 2012, a 46 year-old plant mechanic with 7 years of experience was injured at a crushed stone operation when he fell 16 feet from an elevated walkway of a conveyor to the ground below. The victim and a coworker had been bolting a snub pulley in position. The coworker was positioned on a walkway on the other side of the belt. The victim was hospitalized and died on February 26, 2012.

Best Practices 

  • Establish and discuss safe work procedures. Before starting any work, identify and control all hazards.
  • Train all persons to recognize and understand safe job procedures, including the proper use of fall protection.
  • Always use fall protection when working where a fall hazard exists.
  • Install railings or cables when persons are required to work or travel near the edge of a structure.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #2 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On February 14, 2012, a 40 year-old mine owner with 8 years of experience was killed at a shale operation. The victim was operating an excavator with a rock breaker attachment. He was breaking and mining material from a near vertical wall when the face fell onto the cab of the excavator, crushing him.

Best Practices

  • Operate excavators with the cab and tracks perpendicular to, and away from, the highwall.
  • Bench or slope the material to maintain stability and to safely accommodate the type of equipment used. Do not undercut material on the face of a slope, bank, or highwall.
  • Examine highwalls, slopes, and banks from as many perspectives as possible (bottom, sides, and top/crest) while maintaining the safety of the examiner(s). Look for signs of cracking, bulging, sliding, toppling or other signs of instability. Record the type and location of hazardous conditions.
  • Use auxiliary lighting during non-daylight hours to conduct highwall examinations and to illuminate active work areas.
  • Perform supplemental examinations of highwalls, banks, benches, and sloping terrain in the working area.
  • Immediately remove all personnel exposed to hazardous ground conditions and promptly correct the unsafe conditions. When the conditions can not be corrected, barricade and post signs to prevent entry.
  • Remove loose or overhanging material from the face. Correct hazardous conditions by working from a safe location.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #1 for Metal/Nonmetal Mining 2012

renewcomerLeave a comment

On January 27, 2012, a 69 year-old mobile equipment operator with 48 years of experience was killed at a cement operation. The victim was cleaning a tailpiece with a skid steer loader. He backed the loader in a drainage ditch, traveled in reverse about 150 feet, and went into a 5½-foot deep water hole.

Best Practices

  • Ensure that persons are task trained and understand the hazards associated with the work being performed.
  • Equipment operators should be familiar with their working environment at all times.
  • Ensure that safety precautions are taken based on different weather and lighting conditions.
  • Keep mobile equipment a safe distance from the edge of water or embankments.
  • Barricade or post warning signs at all approaches in areas where health or safety hazards exist that are not immediately obvious to all persons. Warning signs shall be readily visible, legible, and display the nature of the hazard and any protective action required.
  • Provide and maintain berms or guardrails on the banks of roadways where a drop-off exists of sufficient grade or depth to cause a vehicle to overturn or endanger persons in equipment.
  • Monitor personnel’s work activities routinely to determine that safe work procedures are followed.
  • Operate equipment in a manner that maximizes visibility. Use a spotter when visibility of the work or travel areas is limited.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #16 for Metal/Nonmetal Mining 2011

renewcomerLeave a comment

On December 15, 2011, a 22 year-old laborer with 3 months of experience was killed at a surface stone operation. The victim, who was last seen on a control tower, fell into an operating jaw crusher.

Best Practices
 

  • Always use fall protection when working where a fall hazard exists.
  • Establish policies and procedures for safely clearing plugged material in a jaw crusher.
  • Ensure that persons are task trained and understand the hazards associated with the work being performed.
  • Deenergize and Lock-out/tag-out all power sources before working on crushers.
  • Do not place yourself in a position that will expose you to hazards.
  • Monitor personnel routinely to determine that safe work procedures are followed.
Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).