Metal/Nonmetal

Fatality #11 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On June 18, 2010, a 29 year-old contract miner with 6 years of experience was fatally injured at an underground silver mine. The victim was scaling loose ground in a stope when he was struck by falling material approximately 3½ feet long by 2½ feet wide by 2 feet thick.

Best Practices

  • Examine, sound, and test for loose ground in areas before starting to work, after blasting, and as ground conditions warrant.
  • Train all persons to scale loose material safely.
  • Communicate unsafe ground conditions to all affected miners.
  • Perform manual scaling from a location which will not expose persons to injury from falling material.
  • When manually scaling, use scaling bars of a length and design that will allow the removal of loose material without exposing persons to the risk of injury.
  • Install ground support where conditions warrant.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf), Spanish Fatalgram (pdf)

Fatality #10 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On June 12, 2010, a 46-year-old contractor welder was fatally injured at a crushed stone operation. He was preparing to weld on an overhead ventilation duct. The victim was using a ladder to access the duct when he fell over a handrail approximately 45 feet to the ground.

Best Practices

  • Always use fall protection when working where a fall hazard exists.
  • Position ladders to ensure their stability and to eliminate trip hazards.
  • Always face the ladder when climbing or working from a ladder.
  • Do not lean to reach items while standing on a ladder.
  • Always maintain three points of contact with the ladder when climbing.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview(pdf), Spanish Fatalgram (pdf)


Fatality #9 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 28, 2010, a 59-year-old supervisor with 20 years of experience was fatally injured at an underground gold mine. The victim and another miner entered a blast area when a misfire detonated without warning. The other miner was injured and hospitalized.

Best Practices

  • Follow the manufacturers’ guidelines for the storage and usage of explosives.
  • Keep explosives storage areas clean, dry and orderly.
  • Properly rotate explosive stock to use oldest stock first.
  • Never use damaged/deteriorated/outdated explosives, initiation devices, or blasting agents.
  • Wait a minimum of the required times before entering the blast area when either a misfire and/or burning explosives are a possibility.

Click here for: MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf),  Spanish Fatalgram (pdf)

Fatality #8 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 26, 2010, a 28 year-old contract miner with 10 weeks of mining experience was fatally injured at an underground uranium mine. The victim was scaling a rib when he was struck by falling material approximately 11 feet high, 15 feet wide and 4 inches to 30 inches thick.

Best Practices

  • Always examine, sound and test for loose ground in areas before starting to work, after blasting, and as ground conditions warrant.
  • Train all persons to scale loose material safely.
  • Always perform manual scaling from a safe location.
  • When manually scaling, use scaling bars of a length and design that allow the removal of loose material without exposing the persons performing the work.
  • Install ground support in ribs where conditions warrant.

Click here for: MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf), Spanish Fatalgram (pdf)

Fatality #7 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 24, 2010, a 61-year-old maintenance foreman with 32 years of experience was fatally injured at a crushed stone operation. The victim entered a vertical roller mill without locking out the electrical power switch. The mill was started with the victim in the mill.

Best Practices

  • Always follow established lock-out and tag-out procedures.
  • Never rely on others to place your lock on electrical power switches.
  • Always post warning notices at the power switches.
  • Never enter machinery without ensuring the energy source is locked out.
  • Always test to ensure power is off after locking out.
  • Maintain power switch lock out mechanisms to function properly.

Click here for: MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf), Spanish Fatalgram (pdf)

Fatality #6 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 14, 2010, a 35 year-old mechanic/welder with 4 years of experience was fatally injured at a cement operation. The victim was using an oxy- acetylene torch to cut a damaged drill steel to salvage the drill bit. The drill steel exploded causing metal fragments to strike the victim.

Best Practices

  • Always examine materials before applying heat, cutting or welding.
  • Never apply heat to materials without ensuring that flammables/combustibles/explosive materials are not present.
  • Always examine materials with hollow spaces or cavities to ensure gases can vent before applying heat.
  • Never apply heat to materials where pressure build up is possible.

Click here for: MSHA Investigation Report(pdf), Overview(powerpoint), Overview(pdf), Spanish Fatalgram (pdf)

Fatality #5 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 5, 2010, a 21 year-old old contract driller with 1 year of experience was fatally injured at a crushed stone operation. The victim was repositioning a truck mounted drill. He lowered the mast and raised the leveling jacks to move the drill. The drill then rolled down a grade and struck him.

Best Practices

  • Maintain parking brakes to ensure proper function.
  • Always set parking brakes when leaving a vehicle unattended.
  • Ensure parking brake will hold the vehicle before exiting cab.
  • Use tire chocks when parking equipment on grades.
  • Never attempt to enter the cab of a runaway vehicle.

Click here for: MSHA Investigation Report(pdf), Overview(powerpoint), Overview(pdf), Spanish Fatalgram (pdf)

Fatality #4 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On March 24, 2010, a 63 year-old contract truck driver with 21 years of experience was fatally injured at a surface area of an underground salt mine. The victim was loading his truck under a 150 ton salt bin when it collapsed, falling onto the cab of the truck. A second victim working in the area received serious injuries.

Best Practices

  • Routinely examine metal structures for indications of weakened structural soundness (corrosion, fatigue cracks, bent/buckling beams, braces or columns, loose/missing connectors, broken welds, etc.).
  • Keep corrosive material spillage/build-up removed from metal structures.
  • Report all areas where indications of structural weakness are found.

Click here for: MSHA Investigation Report(pdf), Overview(powerpoint), Overview(pdf)

Fatality #2 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On January 26, 2010, a 59 year-old purchasing manager with 5 years of experience was fatally injured at a cement operation. The victim was struck by an over-the-road tandem trailer truck. The truck had been waiting to unload. When the truck pulled forward, another truck driver observed the victim under the second trailer of the truck and immediately stopped the driver. The victim was holding a cell phone at the time of the accident.

Best Practices

  • Train all persons to stay clear of mobile equipment.
  • Be aware of the location and traffic patterns of mobile equipment in your work area.
  • Communicate with mobile equipment operators and ensure they acknowledge your presence.
  • Never approach mobile equipment until you receive confirmation from the operator indicating awareness of your presence.
  • Wear high visibility clothing when working around mobile equipment.
  • Avoid distractions, such as cell phones, when exposed to hazards.
  • Before moving mobile equipment, look in the direction of travel, use all mirrors, cameras, and installed proximity detection devices to ensure no persons are in the intended path.
  • Sound the horn to warn persons of intended movement and wait to give them time to move to a safe location.

Click here for: MSHA Investigation Report(pdf), Overview(powerpoint), Overview(pdf), Spanish Fatalgram(doc)