Coal

Fatality #40 for Coal Mining 2010

renewcomerLeave a comment

COAL MINE FATALITY – On Thursday, July 1, 2010, a 60-year old section electrician was fatally injured when he was run over by a shuttle car. The victim was last seen walking outby the face in a connecting crosscut. As the loaded shuttle car was leaving the continuous miner, the victim was discovered under the shuttle car.

Best Practices

  • Always sound the shuttle car alarm or bell when approaching and before traveling through check curtains.
  • Be aware of your location in relation to movement of equipment, especially in lower coal seams.
  • Wear reflective or florescent clothing to aid visibility when working around mobile equipment.
  • Train miners to use effective means of communication between themselves and equipment operators.
  • Develop and follow standard operating procedures for tramming shuttle cars.
  • Ensure all personnel are clear of the traveling path and turning radius before moving equipment.
  • Pursue new technology such as proximity detection to protect personnel and eliminate accidents of this type.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf)

Fatality #39 for Coal Mining 2010

renewcomerLeave a comment

On June 24, 2010, a 29 year old continuous mining machine operator with 12 years experience received fatal injuries when he was caught between the right rib and the remote controlled continuous mining machine he was operating.

Best Practices
     

  • Install MSHA approved Proximity Detection Systems on continuous mining machines.
    http://www.msha.gov/Accident_Prevention/...
  • Avoid “Red Zone” areas associated with remote controlled continuous mining machines and other mobile equipment.
    http://www.msha.gov/webcasts/coal2004/REDZONE2.pdf
  • Ensure equipment is being operated safely, especially in low mining heights, and slippery and uneven floor conditions.
  • Maintain equipment in a safe operating condition.
  • Observe work practices and provide timely feedback.

    •  

Click here for: MSHA Preliminary Report (pdf), Spanish Fatalgram (pdf), MSHA Investigation Report (pdf).

Fatality #38 for Coal Mining 2010

renewcomerLeave a comment

On Wednesday, June 16, 2010, a 42 year old Section Foreman with 17 years of mining experience was fatally injured. While he was installing rib support, a section of rib 12 feet wide x 15 feet 6 inches high x 9 feet thick fell, knocking over a roof jack that struck him.

Best Practices

  • Conduct roof evaluations when entering a previously mined area for the purpose of pillar recovery.
  • Support loose ribs or roof adequately or scale down material before beginning work.
  • Conduct thorough pre-shift examinations and on-shift examinations of the roof, face, and ribs immediately before work or travel is in an area and thereafter as conditions warrant.
  • Know and follow the approved roof control plan. Take additional measures to protect persons if unusual hazards are encountered.
  • Assure the roof control plan is suitable for prevailing geologic conditions. Revise the plan if conditions change and the support system is not adequate to control the roof, face, and ribs.
  • Be alert to changing geological conditions which may affect roof, rib, and face conditions.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Spanish Fatalgram (pdf)

Fatality #37 for Coal Mining 2010

renewcomerLeave a comment

On Tuesday, June 8, 2010, a 38-year old service truck operator with seven years of mining experience, was fatally injured while in the process of refueling a diesel track-mounted highwall drill. The operator was apparently placing the fuel nozzle into the diesel fuel tank when an ignition/explosion erupted into a fire, engulfing him in flames.

Best Practices

  • Open fuel tank cap slowly to relieve any pressure buildup.
  • Ensure that the refueling area is well ventilated, especially in low areas where heavy fuel vapors can accumulate.
  • Before refueling, turn off the engine(s) and motor(s) and eliminate other potential ignition sources.
  • Check hydraulic lines and connections, especially those near hot surfaces, prior to operating the vehicle. Perform maintenance or repairs when necessary.
  • Ensure that all affected persons are familiar with the Material Safety Data Sheets on fuels and lubricants in use.

Click here for: Spanish Fatalgram (pdf), MSHA Investigation Report (pdf)

Fatality #36 for Coal Mining 2010

renewcomerLeave a comment

On Monday, May 10, 2010, a 55 year old continuous mining machine operator, with approximately 37 years of mining experience, received crushing injuries when he was pinned between a shuttle car and a coal rib. As the loaded shuttle car turned into the last open crosscut, the victim was positioned in the outside turn radius of the shuttle car and was crushed between the shuttle car and the coal rib. The victim passed away on Friday, May 21, 2010 while hospitalized.

Best Practices

  • Make a visual check to ensure all persons are in the clear, and sound the warning device before mobile equipment is trammed, especially in areas where visibility is limited.
  • Ensure good communication between continuous mining machine operators and shuttle car operators so that each is aware of each other’s movements.
  • Wear reflective clothing to aid visibility when working around mobile equipment.
  • Use approved translucent curtains made to allow mobile equipment to tram through.

Click here for: MSHA Investigation Report (pdf)

Fatality #34 & 35 for Coal Mining 2010

renewcomerLeave a comment

On April 28, 2010, the mine roof collapsed at approximately 10:00 p.m., resulting in fatal injuries to a 27-year old continuous miner operator with 3.5 years total mining experience and a 28-year old miner helper with 2 years total mining experience. The roof fall occurred while the miners were loading rock out of a completed extended cut. The fall measured a maximum of 19’9″ in width and 10′ in height. The length of the fall was approximately 70 to 75′ in length, extending toward the face.

Best Practices

  • Assess and examine the adequacy of roof control systems and mining layout for local geology. Know and follow the approved roof control plan.
  • Always conduct a thorough visual examination of the roof, face and ribs immediately before work is performed and thereafter as conditions dictate.
  • When adverse or subnormal roof conditions are present, the mining cut depth should be limited to 20 feet or less. Be alert to changing roof conditions at all times.
  • Ensure that any past roof control issues or history of adverse conditions in adjacent previously mined areas are communicated to all miners and foremen.

Click here for: MSHA Investigation Report (pdf)

Fatality #33 for Coal Mining 2010

renewcomerLeave a comment

On Thursday, April 22, 2010, a 28-year old continuous mining machine operator with 5 years of experience was fatally injured when he was crushed between the conveyor boom of the continuous mining machine and the coal rib. The victim was located near the continuous mining machine while positioning it. The mining height in this area was approximately five feet.

Best Practices

  • Ensure the continuous mining machine operator is positioned beyond the turning radius, and away from the conveyor boom turning radius before starting or moving the equipment.
  • Frequently review, retrain, and discuss avoiding the “RED ZONE” areas when operating or working near a remote controlled continuous mining machine.
  • Pursue new technology, such as proximity detection, to protect personnel from accidents of this type. See the proximity detection single source page on the MSHA web site.
  • Minimize the number of miners working or traveling near continuous mining machines and maintain effective communications between miners and equipment operators.
  • Train all productions crews and management in programs, policies, and procedures for operating remote controlled continuous mining machines.

Click here for: MSHA Investigation Report (pdf), Spanish Fatalgram (pdf)

Fatality #32 for Coal Mining 2010

renewcomerLeave a comment

On April 11, 2010, a 61-year old contract iron worker/mine fireboss with 20 years of mining experience was fatally injured while installing pre-fabricated metal stairs on the side of a fan housing. The stair stringer had been hoisted into place and clamped at the top with two “locking pliers-type” C-clamps. The bottom of the inclined stringer was lying on a 6×6 inch timber. To level the stair treads, a 6×6 inch timber was going to be replaced with a 4×4 inch timber. To replace the 6×6 timber, rigging was fastened near the lower part of the stringer. The victim was standing on the ground holding the handrails. As the lower end of the stringer was hoisted by the crane, the clamps opened and the top end of the stringer fell. This caused the bottom end of the stringer to pivot up and swing out. This pushed the victim backward and pinned him against a nearby manlift.

Best Practices

  • Ensure that all personnel stay clear of hoisted loads and areas where loads may fall if hoisting fails.
  • Know the limitations of temporary supports and ensure they are used within their specifications.
  • Ensure all components are adequately blocked and secured to prevent unintended motion.
  • Use taglines on loads to be hoisted that will need steadying or guidance.
  • Ensure that crane operators communicate with other workers in close proximity to loads that are going to be moved.
  • Ensure that personnel are trained to recognize hazardous work procedures.
  • Discuss work procedures and identify all hazards associated with the work to be performed, along with the methods to protect personnel.

Click here for: MSHA Investigation Report(pdf)

Fatality #3 – #31 for Coal Mining 2010

renewcomerLeave a comment

On Monday, April 5, 2010, 29 miners were fatally injured and 2 miners received serious injuries when an explosion occurred in a large underground coal mine. The victims were located in different areas of the mine, some on their way out of the mine and others were involved with mining activities.

Best Practices

The following best practices are generally applicable to underground mining. An investigation is ongoing at Upper Big Branch which will determine the root cause(s) of the explosion on April 5, 2010.

  • EFFECTIVE VENTILATION SYSTEM – Properly design, frequently examine, and properly maintain a ventilation system that is effective at all times for all areas of the mine. This is the first line of defense against an explosion. Maintain proper air quality in bleeders for examiners.
  • ADEQUATE ROCK DUST – Apply rock dust liberally, even in wet areas, in all faces and outby areas. Maintain the applications to prevent the propagation of coal dust explosions.
  • PROPER EXAMINATIONS and IMMEDIATE CORRECTIVE ACTIONS – Conduct proper pre-shift, on-shift, supplemental, and electrical examinations. Immediately eliminate hazards involving inadequate ventilation, insufficient rock dust, methane accumulations, and permissibility violations.
  • METHANE AND OXYGEN CHECKS – Make frequent methane and oxygen measurements, especially during periods of rapid decline in barometric pressure.
  • COMBUSTIBLE MATERIAL – Clean up loose coal, coal dust, and other combustible material. The possibility of an explosion or fire can be diminished by reducing the fuel supply.
  • WATER SPRAYS and DUST COLLECTORS – Water sprays and dust collectors reduce the fuel available for a potential fire or explosion.
  • ESCAPEWAYS – Conduct escapeway drills and maintain escapeways in safe condition and assure that lifelines are being maintained.
  • ATMOSPHERIC MONITORING SYSTEMS (AMS) – Utilize AMS to monitor strategic locations for carbon monoxide, oxygen content, methane content, and air volumes.

Click here for: Single Source page MSHA Online (web page), Spanish Fatalgram (pdf)

Fatality #2 for Coal Mining 2010

renewcomerLeave a comment

On Friday, January 22, 2010, at approximately 9:15 a.m., a 29 year old continuous miner operator with 12 years of mining experience was fatally injured when a rib roll, approximately 70 inches high, 63 inches long, and 103 inches wide, occurred. The victim was operating a remote control continuous mining machine to clean a previously bolted crosscut when he was struck by the coal rib and pinned against the mine floor.

Best Practices

  • Conduct a thorough visual examination of the roof, face, and ribs immediately before any work or travel is started in an area and thereafter as conditions warrant.
  • Adequately support or scale any loose rib or roof material before beginning work.
  • Perform careful examinations of pillar corners, particularly where the angles formed between entries and crosscuts are less than 90 degrees.
  • Permanently support openings that create an intersection before any work or travel in the intersection.
  • Be alert to changing geologic conditions which may affect roof/rib conditions.

Click here for: MSHA Investigation Report (pdf), Spanish Fatalgram (doc)